Master of Science in Mechanical Engineering (MSME), Wright State University, 2018, Mechanical Engineering

High-lift low-pressure turbine blades produce significant losses at the junction with the endwall. The losses are caused by several complex three-dimensional vortical flow structures, which interact with the blade suction surface boundary layer. This study investigates the unsteady characteristics of these endwall flow structures on a highly loaded research profile and the adjacent endwall using surface-mounted hot-film sensors. Experiments were conducted in a low-speed linear cascade wind tunnel. The front-loaded blade profile was subjected to three different inlet conditions, consisting of two turbulence levels, and three incoming boundary layer thicknesses. Multiple surface-mounted hot-film sensors were installed throughout the passage. This thesis progressed in three stages of research. The first verified that the hot-film sensors could be used to detect flow structures in the cascade. The second used the results from installed hot-films to examine the unsteady characteristics of vortices formed near the leading edge and the propagation of the passage vortex across the passage where it interacts with a corner separation along the suction surface. Simultaneous measurements from the hot-film sensors were analyzed for frequency spectra and time lag in order to provide new insight into the endwall flow dynamics. Finally, signatures from the hot-films were linked to specific flow phenomena through concurrent flow visualization. At each stage of the investigation, results were compared to the results of a numerical simulation.

Committee: Mitch Wolff Ph.D. (Advisor); Rolf Sondergaard Ph.D., P.E. (Committee Member); Christopher Marks Ph.D. (Committee Member) Subjects: Aerospace Engineering; Engineering; Mechanical Engineering

Doctor of Philosophy, The Ohio State University, 1974, Graduate School

Committee: Not Provided (Other) Subjects: Education

Master of Science in Mechanical Engineering (MSME), Wright State University, 2016, Mechanical Engineering

Improvements in turbine design methods have resulted in the development of blade profiles with both high lift and good Reynolds lapse characteristics. An increase in aerodynamic loading of blades in the low pressure turbine section of aircraft gas turbine engines has the potential to reduce engine weight or increase power extraction. Increased blade loading means larger pressure gradients and increased secondary losses near the endwall. Prior work has emphasized the importance of reducing these losses if highly loaded blades are to be utilized. The present study analyzes the secondary flow field of the front-loaded low-pressure turbine blade designated L2F with and without blade profile contouring at the junction of the blade and endwall. The current work explores the loss production mechanisms inside the low pressure turbine cascade. Stereoscopic particle image velocimetry data, total pressure loss data and oil flow visualization are used to describe the secondary flow field. The flow is analyzed in terms of total pressure loss, vorticity, Q-Criterion, Reynolds' stresses, turbulence intensity and turbulence production. The flow description is then expanded upon using an Implicit Large Eddy Simulation of the flow field. The RANS momentum equations contain terms with static pressure derivatives. With some manipulation these equations can be rearranged to form an equation for the change in total pressure along a streamline as a function of velocity only. After simplifying for the flow field in question the equation can be interpreted as the total pressure transport along a streamline. A comparison of the total pressure transport calculated from the velocity components and the total pressure loss is presented and discussed. Peak values of total pressure transport overlap peak values of total pressure loss through and downstream of the passage suggesting that total pressure transport is a useful tool for localizing and predicting loss origins and loss development using (open full item for complete abstract)

Committee: Mitch Wolff Ph.D. (Advisor); Rolf Sondergaard Ph.D. (Committee Member); Rory Roberts Ph.D. (Committee Member) Subjects: Aerospace Engineering; Engineering

PhD, University of Cincinnati, 2015, Engineering and Applied Science: Aerospace Engineering

Increase in emission regulations in the transport industry brings the need to have more efficient engines. A path followed by the automobile industry is to downsize the size of the internal combustion engine and increase the air density at the intake to keep the engine power when needed. Typically a centrifugal compressor is used to force the air into the engine, it can be powered from the engine shaft (superchargers) or extracting energy contained into the hot exhaust gases with a turbine (turbochargers). The flow range of the compressor needs to match the one of the engine. However compressors mass flow operating range is limited by choke on the high end and surge on the low end. In order to extend the operation at low mass flow rates, the use of passive devices for turbocharger centrifugal compressors was explored since the late 80's. Hence, casing treatments including flow recirculation from the inducer part of the compressor have been shown to move the surge limit to lower flows. Yet, the working mechanisms are still not well understood and thus, to optimize the design of this by-pass system, it is necessary to determine the nature of the changes induced by the device both on the dynamic stability of the pressure delivery and on the flow at the inlet. The compressor studied here features a self-recirculating casing treatment at the inlet. The recirculation passage could be blocked to carry a direct comparison between the cases with and without the flow feature. To grasp the effect on compressor stability, pressure measurements were taken in the different constituting elements of the compressor. The study of the mean pressure variations across the operating map showed that the tongue region is a limiting element. Dynamic pressure measurements revealed that the instabilities generated near the inducer when the recirculation is blocked increase the overall instability levels at the compressor outlet and propagating pressure waves starting at the tongue occu (open full item for complete abstract)

Committee: Ephraim Gutmark Ph.D. D.Sc. (Committee Chair); Shaaban Abdallah Ph.D. (Committee Member); Mark Turner Sc.D. (Committee Member) Subjects: Aerospace Materials